PETG บดด้วยเครื่องอัดรีดไดรฟ์โดยตรง
ฉันต่อสู้กับปัญหาการเจียรไส้หลอดมาสองสามสัปดาห์แล้วและฉันก็ติดอยู่
ปัญหาจะปรากฏขึ้นเมื่อเริ่มการพิมพ์ไม่เป็นไรจากนั้นการอัดขึ้นรูปจะหยุดลงในขณะที่เครื่องพิมพ์เคลื่อนที่ไปเรื่อย ๆ เมื่อฉันดึงไส้หลอดออกฉันจะเห็นรอยเยื้องจากเฟืองจากนั้นก็มีรอยกดทับที่มันกราวด์ลงไปที่ไส้หลอด
Filament ที่ใช้คือ 1.75 mm Spool3D PETG บนเครื่องพิมพ์ Hictop ซึ่งเป็นโคลนของ Prusa i3 ฉันไม่รู้หมายเลขชิ้นส่วนที่แน่นอนว่า เครื่องอัดรีดเป็นแบบไดรฟ์โดยตรงและฮีทเบรค 28 มม. เชื่อมต่อกับบล็อกฮีทซิงค์แทนที่จะเป็นแบบที่มีครีบ หัวฉีดมาตรฐาน 0.4 มม.
การตั้งค่าการพิมพ์ของฉันค่อนข้างระมัดระวัง ความเร็วคือ 20 มม. / วินาทีการหดกลับคือ 20 มม. / วินาที (แม้ว่าจะไม่บดเมื่อการหดกลับ) อุณหภูมิ 255 ° C ซึ่งสูงกว่าเครื่องพิมพ์อื่น ๆ ของฉันถึง 10 ° C ไม่มีการระบายความร้อนในการพิมพ์
ตอนแรกฉันคิดว่ามีสิ่งอุดตัน แต่ฉันสามารถดันไส้หลอดด้วยมือได้ดีทีเดียว ฉันยังใช้การทำความสะอาดไส้หลอดบ่อยๆและมันไม่เคยดึงเศษขยะออกมาเลย Heatbreak และหัวฉีดเปลี่ยนเป็นของสด
ใครมีความคิดอื่น ๆ เกี่ยวกับสิ่งที่ฉันสามารถลองได้หรือฉันควรจะได้รับเครื่องอัดรีดใหม่?
คำตอบ
นอกจากนี้สำหรับคำตอบของ @ 0scar :
- If the problem happens in the first layer, it can be that the z-offset is not properly setup: if the first layer is too thin, the printer cannot extrude (enough) plastic, and the filament will warm until the gear cannot extrude it any more. The solution is to have the perfect first layer thickness (so it stick well, but extrude the correct plastic amount).
- Release a bit the gear pressure on the filament: If the gear is too tight, with the temperature, it start to penetrate/deform the filament, and then is not able to move it.
This does sound a lot like you are experiencing the effects of heat creep (How is heat creep characterized?). You should lower the temperature of the hotend and increase the printing speed and retraction speed and possibly lower the retraction length.
If this is heat creep, a new extruder will not help you until you solve the heat creep first. A new hotend that can be cooled better might be a better solution.